Paving & Sandstone Sealer

You don't have to sacrifice appearance in in order for your paving and sandstone to be practical. The Feast Watson Paving and Sandstone Sealer enables your porous stone, masonry and concrete surfaces to gain that beautiful matt or gloss finish, no matter it's traffic area.

With a penetrating, clear sealer, our Sandstone and Paver Sealer offers a heavy-duty protection for high traffic areas such as driveways and garage floors.

Take pride in these areas with a understated and simple matt finish, or a stunning gloss sheen that enhances the stone's natural depth in colour, and know they are protected from stains and traffic wear.

Perfect to use on stamped concrete, sandstone and concrete masonry pavers, terracotta roof tiles and natural brick.

Note: Paving & Sandstone Sealer is NOT recommended for use over acrylic bound pebbles or glazed tiles. It is NOT suitable for areas already affected by salt penetration.

CAUTION: Smooth surfaces may become slippery when wet.

Safety Data Sheet

Find a stockist

WHERE TO USE

Sandstone floors/pavers, stamped concrete, concrete and masonry pavers, brick.

FINISH

Matt

COVERAGE RATE

8m² per litre

NUMBER OF COATS

2 coats

RECOAT TIME

2 hours

DRY TIME

8 hours

CLEAN UP

Xylene

SIZES

1L, 4L, 10L

How to prepare Feast Watson Paving and Sandstone Sealer:

Preparation is key!

Ensure your surface is thoroughly clean and free from oil, grease, dirt and moss prior to applying.
Clean the surface with Feast Watson Floorclean as per the product instructions

For new concrete and aggregate pebbles:

Allow the surface to cure for approximately 28 days then treat surface with a 10% solution (dilute) of Hydrochloric Acid.
Apply Hydrochloric Acid using a brush or mop, allow the acid to remain on the surface for 15 minutes then flush off with clean water. 3. Allow the surface to dry completely before applying Paving & Sandstone Sealer.

How to apply Feast Watson Paving and Sandstone Sealer:

Let's see how to seal your sandstone patio or pavering slabs...

Protect your high traffic areas with these easy steps:

Apply a minimum of two coats of Paving and Sandstone Sealer using either a Feast Watson Floor Finish Applicator, brush, fine mohair or wool roller, to your desired surface.
Make sure to seal all surface edges and ends. This is due to water rising through or behind coatings and can cause a whitening effect.

Are you applying around areas that get regularly wet, such as around swimming pools?

Only apply one coat of Paving & Sandstone Sealer.
Further coats reduce the surface grip when wet and can become a slipping hazard.

Note:
Do NOT apply in temperatures under 10 C or above 35 C or when rain or heavy dew is expected within the coating dry time.

How to maintain your surface after using Feast Watson Paving and Sandstone Sealer:

Always check on your surface to look for any signs of loss of gloss or scratches.
If an additional coat is required, clean using Feast Watson Floorclean. Apply one coat of Paving & Sandstone Sealer as per application instructions.

Floor Clean

Floor Clean is a high quality every day cleaning solutions formulated specifically for timber floors.

Floor Finish Replacement Sock

A replacement sock for the Feast Watson Floor Finish Applicator.

PREPARATION

How to prepare Feast Watson Paving and Sandstone Sealer:

Preparation is key!

Ensure your surface is thoroughly clean and free from oil, grease, dirt and moss prior to applying.
Clean the surface with Feast Watson Floorclean as per the product instructions

For new concrete and aggregate pebbles:

Allow the surface to cure for approximately 28 days then treat surface with a 10% solution (dilute) of Hydrochloric Acid.
Apply Hydrochloric Acid using a brush or mop, allow the acid to remain on the surface for 15 minutes then flush off with clean water. 3. Allow the surface to dry completely before applying Paving & Sandstone Sealer.

APPLICATION

How to apply Feast Watson Paving and Sandstone Sealer:

Let's see how to seal your sandstone patio or pavering slabs...

Protect your high traffic areas with these easy steps:

Apply a minimum of two coats of Paving and Sandstone Sealer using either a Feast Watson Floor Finish Applicator, brush, fine mohair or wool roller, to your desired surface.
Make sure to seal all surface edges and ends. This is due to water rising through or behind coatings and can cause a whitening effect.

Are you applying around areas that get regularly wet, such as around swimming pools?

Only apply one coat of Paving & Sandstone Sealer.
Further coats reduce the surface grip when wet and can become a slipping hazard.

Note:
Do NOT apply in temperatures under 10 C or above 35 C or when rain or heavy dew is expected within the coating dry time.

MAINTENANCE

How to maintain your surface after using Feast Watson Paving and Sandstone Sealer:

Always check on your surface to look for any signs of loss of gloss or scratches.
If an additional coat is required, clean using Feast Watson Floorclean. Apply one coat of Paving & Sandstone Sealer as per application instructions.

Paving & Sandstone Sealer

WHERE TO USE

FINISH

COVERAGE RATE

NUMBER OF COATS

RECOAT TIME

DRY TIME

CLEAN UP

SIZES

Floor Clean

Floor Finish Replacement Sock

PREPARATION

APPLICATION

MAINTENANCE

RELATED PRODUCTS

Floor Clean

Floor Finish Replacement Sock

Get the Look

Decking Re-oil

Feast Your Eyes

Weathered Grey

Natural Look Decking – Traditional Timber Oil