Feast Watson Weatherproof Varnish™
Zoom
Who says weatherproofing wood can’t be exciting?
With a clear, polyurethane formula that gives off a slick, satin or gloss finish, Feast Watson Weatherproof Varnish™ creates an elegant, high-sheen glow while giving maximum UV-screening and protection from the elements.
The perfect way to weatherproof outdoor furniture and for timber exposed to sunlight, salt mist, chemicals, oils and solvents.
Choose from an elegant satin finish or a beautiful high-sheen glow.
You can get a quality clear finish for exterior wood in Australia working for you. Suitable for outdoor furniture, barbecues, doors, trim, handrails, cabin brightwork and window frames.
Note:
- Apply over Feast Watson Timber & Deck Stain to create a gloss or satin finish.
- NOT suitable for heavy wear surfaces (such as decks and walkways). For these areas, use Feast Watson Decking Oil, Traditional Timber Oil, Decking Stain, Timber & Deck Stain or Wet Look Deck.
| Projects |
|
|---|---|
| Sizes |
|
| Where to use |
Outdoor furniture, barbecues, doors, trim, handrails, cabin brightwork, window frames etc |
| Recoat time |
12 hours |
| Coverage rate |
10m² per litre |
| Clean up |
Mineral Turpentine. Soak application cloths in water prior to disposal. |
| Finish |
Gloss |
| Number of coats |
3 Coats |
| Dry time |
24 hours |
How to prepare your timber for Feast Watson Weatherproof Varnish™.
Let's treat your exterior timber.
How to prepare new timber:
Allow new timber to adapt and adjust to the climate in its final position for 4-6 weeks.
Prepare exterior timber for coating with Feast Watson Woodprep. Sand to a smooth surface. Remember to remove all sanding dust before coating.
How to prepare Weathered Timber:
Prepare your exterior weathered or grey timber by cleaning thoroughly with Feast Watson Woodprep.
Sand to a smooth surface. Remember to remove all sanding dust before coating.
How to prepare Previously Coated Timber:
Previously coated surfaces need to be taken back to bare timber by sanding timber to a smooth surface.
Remember to remove all sanding dust before coating.
How to apply Feast Watson Weatherproof Varnish:
Just a few easy steps! Follow these instructions on how to clear coat using Weatherproof Varnish:
Feast Watson Weatherproof Varnish should be stirred thoroughly before and during application with a flat blade stirrer. Take care not to introduce bubbles.
Using a brush, roller or spray, apply Weatherproof Varnish. Spray: Weatherproof Varnish may be thinned by using 10% mineral turpentine if using a spray. Roller: Use a short nap (5mm) mohair roller. Ensure edges and end grain are fully coated.
Make sure to apply a minimum of three coats. Four or more coats may be applied for extra durability, or when the coating has been thinned.
Allow 12 hours drying between coats. Sand lightly between coats.
The final coat should be applied within 30 hours of the previous coat to ensure timber is protected.
How to maintain your timber after using Feast Watson Weatherproof Varnish:
Just a few easy steps to maintain that glow!
Regularly monitor the surface for signs of colour loss or surface defects.
When required, lightly sand the surface and remove sanding dust. Recoat with additional coats of Feast Watson Weatherproof Varnish as per application instructions.
Do not pour leftover product down the drain.
Brush leftover product onto newspaper, and allowed to completely dry, before disposing of via general waste collection.
Empty containers should be left open in a well-ventilated area to dry out. When dry, recycle the container through steel can recycle programs such as Paintback.
Feast Watson Weatherproof Varnish™
Built for harsh outdoor conditions
Resists sunlight, salt mist & spills
Available in satin or high sheen
Select colour range
Colour - Clear Gloss
Colour - Clear Satin
